Installation Floater and Inland Marine Coverage for Modular and Prefabricated Construction in 2026

A module fabricated three hundred miles from the jobsite is still your project — but a standard builders risk policy often does not follow it to the plant or onto the truck. The gap is closed with inland marine, deliberately.

Modular and prefabricated construction has moved from novelty to method. Driven by labor shortages, compressed schedules, and the quality control a factory setting allows, more contractors are building in a plant and assembling on site. The approach can take months off a timeline. What it also does — quietly — is move a large share of a project's value off the jobsite and onto a factory floor and a flatbed trailer, two places a traditional builders risk policy was never written to reach.

The gap begins with how builders risk is defined. A standard builders risk policy insures property at the described project site. Materials and components under construction at an offsite fabrication facility, and the finished modules moving in transit, frequently fall outside that definition or are capped by a token sublimit that bears no relationship to the true value in motion. Worse, until a module is delivered and accepted, it may legally remain the fabricator's property — covered, if at all, only by the fabricator's own policy, or by no one's. A loss at the plant can land in a coverage no-man's-land that neither party priced for.

This is where the installation floater earns its place. An installation floater is an inland marine form built to cover materials and equipment a contractor will install, from the point the contractor takes responsibility through delivery, temporary storage, and installation — and, critically, while those items are in transit. For modular work, an installation floater, or a builders risk policy specifically endorsed with offsite storage and transit extensions, is the instrument that follows the module from the factory to its final position. The coverage tracks the property rather than the address.

Transit is the acute exposure, because a module is never more vulnerable than on the road. An oversized component can be damaged by a bridge strike, a shifted load, an overturn, or weather, and the question of who bears that risk depends entirely on the contract terms and the point of delivery. A contractor who assumes the shipment is "the trucker's problem" often discovers the motor carrier's cargo limit is a fraction of the module's value. Scheduled transit limits and offsite storage limits must be sized to a full module — the real number — not to the modest default a boilerplate form carries. The limit has to match the cargo on the trailer, not the convention printed in the form.

Valuation and concentration raise the stakes further. On a modular project, a single unit can represent a substantial percentage of the contract value, so one destroyed module is not a line-item loss — it is a schedule event that can stall the entire assembly sequence. Re-fabricating a custom unit carries its own lead time, and the delay ripples into financing, liquidated damages, and lost use. This is why delay-in-start-up and soft-costs coverage belongs in the conversation alongside the physical-damage limit: the direct loss is the module, but the expensive loss is often the time.

None of this holds together without contractual discipline. The fabricator should be required to carry adequate property coverage on work in its care, to name the contractor as an additional insured, and to provide a waiver of subrogation. The builders risk policy, the installation floater, and the fabricator's property policy then have to be read together so there is neither a gap where each assumes the other responds, nor an "other insurance" dispute that leaves the contractor funding a loss while two carriers argue. Allocation of risk on a modular job is not a certificate; it is a structure that has to be assembled as deliberately as the building.

This is the work our 4-Step Strategic Process is built to do. Strategic Discovery maps every point at which a project's value sits offsite or in transit, and the contracts that govern each handoff. Risk Assessment tests the builders risk, installation floater, and transit limits against the full value of a single module and the catastrophic schedule loss its destruction would cause. Solution Design closes the offsite and transit gaps, sizes the limits to the real exposure, and aligns the policies so they respond as one. Ongoing Optimization keeps the coverage current as the fabrication schedule and the module values change through the job.

Modular construction rewards contractors who think in systems, and insurance is one of those systems. The method moves faster than stick-built work precisely because so much happens before anything reaches the site. The coverage has to move with it — off the jobsite, onto the truck, and into the factory — or the efficiency that makes modular attractive becomes the exposure that makes a loss uninsured.

— Ryan Mefford, President & Risk Advisor